3D drawings of Master BMS
3D drawings of Saster BMS
3D Drawing of Slave BMS .zipBy the way , Kindly Reminding：Please order "other accessories " when you order master bms and slave bms
since"other accessories " include precharge relay ,charge relay, discharge relay ,ON-OFF switch relay,RS485-to USB Converter,Pre-charging resistor ,Shunt , Fuse ,Photovoltaic anti-reverse diode ,
Diodes , Balancing wires ,Emergency Stop Button ,Start Button, etc.
High voltage box need to be gounded ;Inverter need to be grounded;
Battery case need to be grounded;
Old version of HV BMS wiring scheme :
Wiring diagram of high voltage BMS with heating (REL5)/cooling(REL6)
Wiring diagram of high voltage BMS without heating (REL5)/cooling(REL6)
For better resolution of bms diagram ,please check the inserted PDF file;
Connection Diagram of HV BMS.pdf
New Version of HV BMS wiring scheme :
For better resolution of bms diagram ,please check the inserted PDF file;
New Version of BMS wiring scheme_V1.6.pdf
Attention : when you do wiring , please check whether or not the ground of the DC-DC power supply is connected to the
housing of the high Voltage box, and the housing of the high voltage box should be grounded. And the case of all batteries
should also be grounded!
This bms can talk to inverter：
(DEYE/GOODWE/ATESS/INVT_BD/PYLON/GROWATT/SOFAR/MEGAREVO/KOYOE/SOLAX/SOLIS)
During assembly ,some points for attention
Please be sure that the inverter /High voltage box /slave bms go to be grounded ;
otherwise , the canbus communication distortion occurs
please be aware that each slave bms need to be grounded
High voltage box need to be grounded
Inverter needs to be grounded
How to connect bms to Deye Via cabus communication ?, please see below :
1. First of all , you need to select " PYLON-HV 派能(500K)"
2.Please use RJ 45 cable to connect master bms to BMS port of DEYE
PIN Definition of BMS PORT of DEYE
according to above pin definition of bms port , you can see that only 2 cables of CAN -H and CAN-L are kept for connection between master bms and DEYE ; please see below
CAN-H and CAN-L at BMS port of DEYE
CAN-H and CAN-L at J2 port of Master BMS
afterwards ,you need to connect Cable of CAN-H and CAN-L of master bms and Cable of CAN-H and CAN-L of DEYE together
and then connection between bms and deye is completed ;
Finally you need set "00" in the battery mode of DEYE
BMS Basic Protocals (Modbus Protocals)
HV BMS Modbus Protocals_EN-TOPBMS.pdf
User Manual -English version
Display Instruction of HV BMS- TOPBMS.pdf
Instruction of Master BMS Configuration -TOPBMS.pdf
Master BMS Configuration Via RS485 to USB - TOPBMS.pdf
Master BMS Configuration PC Softwarfe(Password: 123456)
The lastest Version of BMS Newest Firmware
HW17X_V512-Newest Firmware.rar
Configuration for Different Inverters and flash Inverter protocals into Master BMS
(DEYE,GOODWE,ATESS,SOFAR,INVT_BD,PYLON,GROWATT,MEGAREVO,KOYOE,AFOFE,Solax,Solis，
Sunways,SINEXCEL-PCS,AISWEI ,Bluesun,FOX ESS,Luxpower)
How to change language of pc software ?
How to enter passowrd before you configurate bms ? See below
Master BMS is used to configurate the charging cut-off / discharging cut-off /Over current cut-off / Balance starting /Inverter Communication / Inverter charging cut-off / Invert discharging cut-off /Cell strings ,etc. Let me take BMS 48S for example ,
please see the following configuration
If you use slave bms 32s , please don't enter " 32" and "6";
you shall enter " 16 " and"3"+"16"and "3"
Attentions :for slave bms 32 S , you need to do setting in the pc software in this way : slave bms 32s = 2* slave bms 16s ; you need to enter 8 at Pack Nums+2 * 16 at Cell Nums + 2* 3 at Tempr Nums;
Entering 4 at pack Nums +32 at each Cell Nums +6 at Tempr Nums is not allowed ; BMS cannot work ;
Take 128S for example : you need to enter enter 8 * 16 at Cell Nums + 8* 3 at Tempr Nums;
What is the standby current ?
Standby current means BMS self power consumption which is 500mA ; Please enter 500 here ;Please see below :
What is the Zero Diff
Before you set /calculate SOC , please enter password: 123456;
How to get correct SOC now?
Set the design capacity / full capacitu / residual capacity in the pc software as below ;
regarding the residual capacity , please enter 1/2 full capacity
and then take a complet cycle of discharging and charging ; finally the SOC will be calibrated automatically
How to calibrate the current ?
Please adjust the FL CHG/FLDSG factors if charge current discharge current is not in line with actual current
Before current calibration , please check if the setting of shunt is in line with the actual parameters of the shunt you use
How to set " Standy by curremt "，“Zero diff Current ” , "Zero Current"
How to set cell balancing in the PC software ?
HV BMS Montoring User Manual
How to get display work ?
if you don't select "DWIN TFT" , the display show all " 0"
Display Instruction of HV BMS- TOPBMS
Display Instruction of HV BMS- TOPBMS.pdf
Cable for RS485 to USB
Driver Software (UT-8890)of Converter of RS485 to USB
Driver Software (UT-885/890/2003A/880/8801)of Converter of RS485 to USB
UT-885、890、2003A、880、8801 DRIVER.rar
Driver Software (CH340 for Win11)
Driver Software (CH340 for Win7,8,9,10)
CH348 Driver for win7 ，8 ，10.zip
you need to change the settings of converter via RS485 transmission cable ; if not , the converter cannot work properly
Master BMS Firmware Update :
Battery capacity Settings in the BMS Monitoring Systerm Software
Slave BMS DIP CODE ： each slave bms has one dip code ; the rule as following :
Slave bms connected in series
Slave Bms can control 6-16cells （Max 16 cells）; It means the slave bms has downwards compatibility ; the wiring diagram as following :
Slave Bms can control 6-16cells （Max 16 cells）; It means the slave bms has downwards compatibility ; the wiring diagram as following :
Interface Decription of Slave bms
Interface Decription of Master bms
How to Use /Wire DCDC converter :
How to Wire Display or Wire Inverter with RS485 Port
